RapidAir kits are prepackaged shop air systems: flexible tubing, fittings, manifolds, and supports sold together. Whatever the kit, the installation follows the same sequence: plan, mount supports, straighten and cut the tube, fit the fittings, connect the compressor end, and test. The steps below describe that general sequence. Your kit’s manual sets the exact tube handling, fitting, and support spacing. If anything here differs from the manual, follow the manual.
Before you start: check the kit
- Check the contents against the packing list. Confirm the tubing lengths, fittings, manifold blocks, drop components, supports, and the cutting and deburring tool.
- Confirm the tubing size. Smaller and larger tubing suit different runs and tool demands. Decide the size before you cut.
- Check the printed pressure and temperature rating on the tubing and fittings. Your compressor’s maximum pressure, shown on its nameplate or tank decal, must be within that rating.
- Gather basic tools: a tape measure, a level, a drill and bits, screws suited to your wall, and soapy water for testing.
Step 1: Plan the route
- Draw the layout. Mark the compressor outlet, the main run, each branch, each drop, and any hose reel location.
- Measure the actual run, then add a little for bends and fittings. Measure twice before cutting.
- Choose a height for overhead or wall runs that keeps the line clear of ladders, doors, and hoists.
- Place drains at low points so condensed water has a way out.
Step 2: Mount the supports
- Mark support locations at the spacing the manual gives. Tubing sags between supports.
- Fasten supports into studs or solid backing. One installer found the supplied plastic standoffs too short to reach solid wood and used longer screws. Check that yours hold firmly.
- Keep runs level and parallel so they look tidy and don’t rub against the wall.
Step 3: Uncoil and straighten the tubing
- Coiled tubing keeps its curl. Unroll it along the route before you cut.
- Straighten the sections by hand. Long lengths take patience and a helper. A tubing straightener is an optional tool for long runs.
Step 4: Cut and deburr
- Cut each length square with the cutter the kit provides. An angled cut can prevent a full seal.
- Deburr the inside edge with the included tool, so the tube slides into the fitting without catching or shaving.
- Check each cut against the layout before you cut the next piece.
Step 5: Fit the fittings and manifolds
- Push the tube fully into each fitting until it bottoms out. Partial insertion is the most common cause of leaks in push-to-connect and compression systems.
- Use the fittings the kit provides: straight connectors, elbows, tees, and plugs for unused outlets.
- Mount the manifold and distribution blocks. Manifold blocks are often wider than a stud, so you may need a standoff bracket.
- Tighten retainers or compression nuts to the point your manual gives. Overtightening can crack fittings.
Step 6: Connect the compressor end
- Install a shutoff valve, a leader or whip hose, and a water separator or filter near the compressor. See how to set up air compressor lines for the full order.
- Add a regulator and drain at this point if your kit includes them, or if you plan to use FRL units.
- Check the flow arrows on the filter and regulator match the direction of air.
Step 7: Add drops and quick disconnects
- Install each drop with a shutoff valve and a drain at its bottom. See shutoff valves and drop legs.
- Use quick-disconnect couplers at each outlet. Match the coupler style to your hose and tools. See air coupler types.
Step 8: Pressurize and test for leaks
- Set the regulator to a low pressure for the first test.
- Close all outlets and let the system pressurize.
- Brush soapy water on every joint, fitting, and bend.
- Mark each bubble, depressurize, correct the fitting, and retest.
- Raise the system to working pressure and watch the gauge over a period of time. A steady drop means a leak remains.
For more methods, see finding and fixing compressed air leaks.
Common problems and fixes
- Leak at a fitting: The tube probably isn’t fully seated. Depressurize, re-cut the end square, and push it in until it bottoms out.
- Waves between supports: Coiled tubing keeps its shape. Tighten the supports and straighten by hand where you can.
- Manifold won’t sit flat: Use a standoff or spacer. Don’t force the block against a stud.
- A far outlet feels weak: Check the regulator setting, the drop size, and for kinks in the tubing.
Is a kit right for you?
A kit can be quicker to assemble than rigid pipe, with fewer tools and no soldering or threading. The trade-offs are the cost of matched parts, the effort of straightening coiled tubing, and the need to keep using that kit’s fittings if you expand the system later. For a permanent shop, compare the options in air compressor line setup, and see PEX for air compressor lines for another plastic tubing option.