Standard PEX is not a good default for compressed air, and many manufacturers don’t rate it for that use. PEX-AL-PEX, a version with an aluminum layer, is sold for shop air in some kits, but only within the ratings printed on the product. If you want the most conservative permanent line, metal pipe is the better choice. The rest of this article explains the differences.
Can I use PEX tubing for compressed air lines?
Plastic tubing can be used for some compressed air lines, but only if the product is rated for air at your compressor’s maximum pressure and at the temperatures in your shop. The first question is which kind of PEX you have.
Standard PEX
Standard cross-linked polyethylene (PEX) is designed mainly for water and heating. Its ratings are usually based on water at a set temperature, and many manufacturers don’t list it for compressed air. Heat and UV light can also make it brittle over time. Compressed air stores energy, so a failure under pressure can be sudden and hazardous.
PEX-AL-PEX
PEX-AL-PEX has a layer of aluminum bonded between two PEX layers. It is commonly sold for compressed air kits, often in blue, with matching fittings. Its rating depends on the specific product, so read the label. Some kits list a rating of around 200 psi at room temperature. Treat any figure as a starting point and confirm it on your product. Your compressor’s maximum pressure is on its nameplate or tank decal.
What is the difference between PEX and PEX-AL-PEX?
| Feature | Standard PEX | PEX-AL-PEX |
|---|---|---|
| Construction | One layer of cross-linked polyethylene | PEX layers around an aluminum core |
| Shape | Bends easily, but can spring back | Holds a bend better and expands less with heat |
| Fittings | Usually crimp or expansion fittings | Usually compression fittings sold with the kit |
| Compressed air use | Generally not rated; check the manufacturer | Sold for shop air with matched, rated fittings |
Is PEX pipe better than PVC?
For compressed air, many guides consider PEX-AL-PEX a safer choice than PVC, because PVC is brittle and can shatter. PVC gets more brittle over time, and oil and heat in the air speed that up. Standard PEX is not a clear win over PVC for compressed air, since many makers don’t rate it for air. Neither plastic matches metal for durability or temperature range. See why PVC is not recommended for the details.
Pros and cons of PEX-AL-PEX for shop air
Pros
- Light and easy to route around joists, corners, and tight spaces.
- Corrosion-free. It won’t rust or shed scale into the air stream.
- Fewer joints than rigid pipe over the same run, so fewer places to leak.
- No soldering or threading. Kit fittings go together with a cutter and a few basic tools.
Cons
- Ratings drop as temperature rises. Hot air straight from the compressor is a concern.
- Sunlight degrades plastic. Keep lines indoors or shielded from direct sun.
- Fittings must match. Mixing brands can cause leaks or failures.
- Coiled tubing keeps its curl. It can be hard to straighten over long lengths.
- It needs more support than rigid pipe to stay in place.
Pre-packaged systems such as RapidAir use their own tubing and fittings, so the rating on the kit governs what you can do with it.
Heat, sunlight, and burial
Keep it cool
Hot discharge from the pump can soften plastic and reduce its rating. A short run of metal pipe at the tank, or an aftercooler, can help cool the air before it reaches plastic tubing. Keep the tubing away from the compressor head.
Keep it out of sunlight
UV light degrades PEX over time. Run lines indoors, or shield them from direct sun.
Don’t bury it
Compressed air lines aren’t generally intended for burial. Unless the manufacturer specifically rates the product for underground use, keep it above ground, where you can inspect it.
Installation tips
- Cut square with the cutter the kit recommends, and deburr the inside edge.
- Push the tube fully into each fitting until it bottoms out. Partial insertion is a common leak source.
- Support every run as the kit’s instructions describe, with clips or straps.
- Add a water separator or drain at low points. The tubing itself won’t drain.
- Avoid kinks at bends. Follow the kit’s minimum bend guidance.
When to choose metal instead
If the line is permanent, runs near heat or sun, or feeds tools that need clean air, metal pipe is the more conservative choice. Aluminum, copper, and black iron are all common options. Plastic tubing can be a reasonable choice for a small indoor setup with a kit rated for air at your compressor’s maximum pressure. For the whole layout, see how to set up air compressor lines. For the metal option, see black iron pipe for air compressor lines.