Yes, compressed air usually comes out wet. Air always carries some water vapor. Compression makes it easier for that vapor to condense as the air cools in the tank and pipes. Separators and filters catch the liquid water. Only a dryer lowers the dew point and removes the vapor. Whether you need a dryer depends on what the air is used for and how cold your lines get.
Does compressed air come out wet?
Yes. The water in the air is packed into a smaller volume when the air is compressed, and as the air cools in the tank and lines, some of it condenses. That is why the tank drain fills up. Most of what you see is liquid water. The vapor that remains can condense later, farther downstream, where the air is cooler.
Liquid water vs. water vapor
- Liquid water is removed with water separators, moisture traps, drains, and coalescing filters. These catch droplets.
- Water vapor is removed only by a dryer. A dryer lowers the dew point, so less water condenses downstream.
An aftercooler cools the air and removes much of the liquid, but it does not dry the air to a set dew point. Many portable compressors include an aftercooler and a separator. Neither one is a dryer.
What is dew point?
Dew point is the temperature at which water vapor in the air starts to condense. A lower dew point means drier air. For compressed air, the pressure dew point matters most, because it describes condensation at line pressure. The lower the pressure dew point, the less water can condense at ordinary shop temperatures.
ISO 8573-1 sets purity classes for compressed air, including pressure dew point. It is a useful reference for describing air quality, but it doesn’t tell you which class you need. That depends on your use.
What is the dew point limit for compressed air?
There is no single universal limit. The dew point you need depends on your application and environment.
- General shop use, such as air tools, inflation, and blow-off, usually doesn’t need very dry air.
- Lines that run through freezing areas need a dew point below the lowest temperature they will see. Otherwise condensate can freeze and block the line.
- Painting, sandblasting, electronics, and food or medical work often need much drier air. The equipment maker or the process specification should set the target.
Types of dryers
Refrigerated dryers
A refrigerant circuit chills the air, condensing the water vapor, which is then drained. Refrigerated dryers commonly reach a pressure dew point around 35°F. They need electricity, and the condenser and drain need regular cleaning. They suit indoor shops where lines don’t freeze.
Desiccant dryers
Desiccant dryers pass air through a material that adsorbs moisture. Twin-tower designs alternate between two towers, regenerating one while the other works. They can reach very low dew points, around -40°F, which suits outdoor lines, cold areas, and sensitive processes. They cost more to run, and the desiccant must be replaced periodically.
Membrane dryers
Membrane dryers pass air through hollow fibers that let water vapor permeate through the walls. They need little maintenance and suit small flows, such as lab or instrument air. Part of the dried air is used to sweep the membrane, so the dryer doesn’t deliver all of its inlet air.
Deliquescent dryers
Deliquescent dryers use a moisture-absorbing material that dissolves as it takes up water. They need no electricity, but the media is used up and must be replaced. They suit intermittent use and places without power.
Aftercoolers (not dryers)
An aftercooler cools the air just after the compressor and removes most of the liquid water. It is a useful first step, but it is not a dryer.
What is the best air dryer for an air compressor?
No single dryer is best. Choose by the dew point you need, the flow rate, space, power, and upkeep.
| Type | Typical dew point | Power | Upkeep | Typical fit |
|---|---|---|---|---|
| Refrigerated | Around 35°F | Electric | Clean condenser and drain | Indoor general shop use |
| Desiccant | Down to around -40°F | Often none, heat for heated types | Replace desiccant periodically | Cold areas, sensitive work |
| Membrane | Modest reduction | None | Keep pre-filters serviced | Small flows, lab or instruments |
| Deliquescent | Modest reduction | None | Replace media | Intermittent use, no power |
Filter and dryer order
A typical order from the compressor is:
- Aftercooler, if present
- Water separator with a drain
- Dryer, if you need one
- Particulate filter
- Regulator at the tool
Desiccant and membrane dryers need protection. Liquid water and oil (from an oil-lubricated pump) can damage them, so install a coalescing pre-filter ahead of the dryer. Then add a filter after it if the air needs to be clean for the work.
Maintenance
- Drain separators and the tank daily, or after each use in humid weather, as part of your regular compressor maintenance.
- Clean the refrigerated dryer condenser and check that its automatic drain works.
- Replace filter elements on the schedule the maker gives.
- Replace desiccant as the maker specifies.
- Watch for condensation at the outlet. Droplets or a damp tool line mean the dryer or drain needs attention.
When you may not need a dryer
A separator and drain may be enough for blow-off, inflating tires, or general tool use in a heated space. A dryer is worth the cost when condensation causes damage or problems, such as in painting, sandblasting, pneumatic instruments, or lines that run outdoors in cold weather.
For the wider line layout, see how to set up air compressor lines. For draining the tank as part of starting a compressor, see how to start an air compressor. For leaks, which also let moisture in, see finding and fixing compressed air leaks.