You cannot add CFM to a compressor’s pump with settings or accessories. The pump and motor set how much air the compressor makes. What you can do is stop losing air, reduce restrictions between the compressor and the tool, keep the pump working at full output, and, if the compressor is still too small, buy one that is rated for the job.
What CFM means, and what your tool needs
CFM, or cubic feet per minute, is the volume of air a compressor delivers each minute. Ratings only compare fairly when they are stated at the same pressure. A rating taken at a lower pressure can make a compressor look more capable than it is at the pressure your tool needs.
Check the tool’s label or manual for its CFM requirement at its working pressure. Compare that with the compressor’s rating at the same pressure. A nailer uses air in short bursts, so a small compressor can keep up with it. A sander or impact wrench runs continuously, and many small compressors cannot keep up with that load.
Step 1: Find and fix air leaks
Leaks waste output and make the pump run more often. A small leak can waste a large share of what the compressor makes.
- Mix dish soap and water in a spray bottle.
- With the tank pressurized, spray the fittings, quick-connects, hose ends, the drain valve, the pressure switch, and the tank seams.
- Bubbles mean a leak. Tighten the fitting or replace its seal, then test again.
Do not overtighten fittings, because they can crack. The testing and inspection guide has more on leak checks.
Step 2: Remove restrictions between the compressor and the tool
Restrictions cut the airflow that reaches the tool, even when the compressor is making plenty of air.
- Hose diameter. A 1/4-inch hose limits flow more than a 3/8-inch hose does for tools that use a lot of air.
- Hose length. Longer hoses lose more pressure. Use the shortest practical length.
- Fittings and couplers. Small or restrictive quick-connects, bushings, and tiny inline fittings reduce flow. Use fittings with a full-size opening where you can.
- Regulators and filters. A small regulator or filter restricts airflow. Check the flow rating of each one against your tool.
- Water separators and dryers. These also restrict flow. Pick one rated for the airflow you need.
Do not remove a filter or water separator to gain flow. Moisture and dirt damage tools. Choose a higher-flow model instead.
Step 3: Keep the pump at full output
A healthy pump delivers its rated airflow. Common reasons it does not:
- A clogged intake filter. Clean or replace it as the manual says.
- Low or dirty oil on oil-lubricated units. See how often to change air compressor oil.
- Worn or leaking valves and rings. These show up as slow pressure build and a gradual loss of output. The pump may need repair or replacement.
- A check valve or unloader problem. See unloader valve symptoms.
- A loose or worn drive belt on belt-driven units, which slips and lowers pump speed.
- Heat. A hot pump loses efficiency. See air-cooled compressor overheating.
Step 4: Set pressure for the tool, not higher
Set the regulator to the tool’s rated working pressure. Raising the tank pressure does not make the pump deliver more CFM. Higher pressure also increases leak losses and adds stress to hoses and fittings.
Never raise the pressure switch cut-out above the tank’s maximum rated pressure to get more air. That is a serious hazard.
Step 5: Upgrade when the numbers do not work
Suppose the leaks are fixed, the restrictions are cleared, and the pump is healthy, but the tool still runs out of air. The compressor is then too small for that tool at its working pressure. Your options are:
- A compressor with a larger pump and motor, rated at the pressure your tool needs. See air compressor types and sizes.
- A unit built for continuous duty, if your tools run for long periods.
For tools that use a lot of air, a larger tank helps only a little, because the pump is still the limit.
Tank size and CFM
| Change | What it does | What it does not do |
|---|---|---|
| Larger tank | Stores more air, so the pump runs less often during short tool bursts | Does not add CFM. Continuous tools still drain it |
| Larger pump and motor | Raises the rate of air production | Does not fix leaks or narrow hoses |
| Fixing leaks | Keeps more of the air the pump makes at the tool | Does not add pump capacity |
| Wider hose and fewer restrictions | Delivers more of the air the pump makes | Does not add pump capacity |
| Higher tank pressure | Raises the stored pressure | Does not raise rated CFM, and adds stress |
Frequently asked questions
Does a bigger tank add CFM?
No. A bigger tank holds more air and lengthens the time between pump cycles. It does not change how much air the pump makes each minute. For tools that run continuously, the pump’s CFM is what matters.
Does lowering the pressure give more CFM?
Not in a way you can count on. Ratings change with pressure, and a tool’s CFM requirement applies at its own working pressure. Set the regulator to what the tool needs, and compare the compressor’s rating at that same pressure.
Is more PSI the same as more CFM?
No. PSI is pressure, and CFM is volume per minute. A compressor can have a high PSI rating and still deliver little air. Small compressors often have this profile, so check the CFM rating before you buy.