The short answer
CFM and SCFM both measure airflow, the volume of air a compressor delivers each minute. SCFM is corrected to a standard set of reference conditions so that ratings from different compressors can be compared fairly. To check whether a compressor can run a tool, compare the airflow at the same pressure, usually 90 PSI.
What CFM means
CFM stands for cubic feet per minute. For a compressor, it is the volume of air the unit delivers in one minute at a stated pressure. It is not the tank size, and it is not the maximum PSI.
CFM is always tied to a pressure. A compressor’s airflow changes as the pressure changes, so a CFM figure without a pressure is incomplete.
What SCFM means and why it exists
SCFM stands for standard cubic feet per minute. It is airflow converted to standard reference conditions for temperature, pressure, and humidity. That conversion lets manufacturers compare units on the same basis, even if they were tested in different places.
The reference conditions are set by a standard, and different standards use different values. Two sources can list slightly different reference conditions for SCFM. So when you compare two ratings, check that both use the same basis, and do not treat one set of reference numbers as universal.
Why real output can fall short of the label
Air is less dense in hot, humid, or high-altitude conditions. A compressor’s real output in those conditions can be lower than its rated SCFM. This is one reason to leave margin on top of a tool’s requirement.
Where you will see the pressure: 90 PSI and 40 PSI
Flow ratings are often given at more than one pressure. A compressor’s sticker might list one airflow at 40 PSI and a lower airflow at 90 PSI. Both figures can be correct for their pressure. The one that matters for most tools is the figure at the tool’s operating pressure, which is often 90 PSI.
Do not compare a 40 PSI figure with a tool’s 90 PSI requirement. The compressor will not deliver the higher number to a tool that runs at 90 PSI.
Matching airflow to your tools
- List every tool you plan to run.
- Find each tool’s airflow requirement at its operating pressure, usually 90 PSI.
- Add the requirements for tools you would run at the same time. Do not add tools you would never use together.
- Add a margin. Guides differ on how much. Some suggest about 20 to 25 percent. Others multiply the total by 1.5. Either is a judgment call, and a continuous tool calls for more margin than a tool used in short bursts.
- Compare the total with the compressor’s rating at 90 PSI.
A worked example
This example uses round numbers for illustration only. Check the labels for your own tools.
Suppose you plan to run two tools at once. Tool A needs 2 CFM at 90 PSI, and tool B needs 3 CFM at 90 PSI. The total is 5 CFM. Adding about 20 percent gives a target of roughly 6 CFM at 90 PSI. A compressor rated at 4 CFM at 90 PSI would fall short for that pair, even if its maximum PSI is high.
If you run only one of the tools at a time, the total drops, and a smaller compressor may still be enough.
Tank size is not airflow
Tank size controls how long a tool can run before the motor restarts. Airflow controls whether the compressor can keep up with the tool. A large tank with low airflow can run a short burst of work and then stall on a continuous tool. A small tank with high airflow can refill quickly but still cycle often. You need both to fit your work.
For a short starter-size example, see is a 3 gallon air compressor big enough.
Common mistakes
- Comparing an SCFM figure with another brand’s CFM figure without checking the basis.
- Reading the 40 PSI figure as if it were the 90 PSI figure.
- Using maximum tank PSI as a measure of airflow.
- Choosing the highest CFM available, rather than the airflow your tools need.
- Ignoring duty cycle, which affects how long a unit can run without rest.
What to look for on a spec sheet
- The airflow figure, with its unit (CFM or SCFM).
- The pressure at which the airflow is rated, usually 90 PSI.
- The tank size and maximum tank pressure.
- The duty cycle and the voltage and amps on the nameplate.
For a closer look at reading one rating, see what does 4.0 SCFM at 90 PSI mean. For how pressure relates to tank rating, see how much PSI a pancake compressor has.
Bottom line
Compare airflow at the same pressure, usually 90 PSI, and check that both ratings use the same basis. Add a margin for real-world conditions and continuous tools. Use the air compressor types and sizes guide to put airflow, tank size, and power together.