Maintenance and Repair

How Often to Change Air Compressor Oil (and Which Oil to Use)

Find out how often to change air compressor oil, which non-detergent oil to use, and how to refill without overfilling. Start with your manual.

On this page
  1. Does your compressor use oil?
  2. How often to change the oil
  3. Which oil to use
  4. How to change the oil
  5. Signs the oil needs changing now
  6. Overfilling and oil in the air
  7. Frequently asked questions

Follow the oil change interval in your compressor’s manual. Many manuals list a run-hour interval, a calendar limit, or both. If both are given, change the oil at whichever comes first. If you cannot find the manual, change the oil at least once a year, and sooner if you use the compressor heavily or it runs in a dusty or hot shop. Oil-free compressors have no oil to change.

Does your compressor use oil?

Most small piston compressors with a crankcase sump are oil-lubricated. Look for:

  • A sight glass on the pump or sump.
  • A dipstick or an oil fill cap.
  • Oil fill instructions in the manual.

Oil-free compressors have none of these. Do not add oil to a unit the manual calls oil-free. Check the manual before you add anything.

How often to change the oil

Oil intervals vary a lot between models, and published numbers from different sources often conflict. Use these rules instead of a single table:

  1. Manual first. It gives the interval for your model, usually in run hours, a calendar limit, or both.
  2. Whichever comes first. If the manual gives both, follow the one you reach first.
  3. Break-in change. Some manuals call for an early oil change after the first few hours of break-in. Check for this on a new unit.
  4. Sooner for hard use. Dusty shops, hot rooms, and heavy daily use all shorten oil life.
  5. Oil ages even when idle. Oil left in a unit for a long time breaks down and absorbs moisture, so change it before long storage if it has been used since its last change.
  6. Check it often. On heavy use, check the level at least weekly, and keep a note of run hours if the unit has an hour meter.

Which oil to use

  • Use compressor oil, not motor oil. Motor oil contains detergents that keep engines clean. In a compressor, those detergents can cause foaming and carry more oil into the air line.
  • Use non-detergent oil. Compressor oil is typically non-detergent. Many small piston compressors call for a specific viscosity; a common example is SAE 30 non-detergent. Use the grade your manual lists.
  • Mineral or synthetic. Mineral oil is the common, lower-cost choice. Synthetic oil often handles heat better and can last longer, but use it only if the manual allows it.
  • Do not mix types or brands without checking the manual. When you switch, drain the old oil and refill rather than topping up.
  • Rotary screw units use specific oils from the manufacturer. Follow the manual.

How to change the oil

  1. Unplug the compressor and release all pressure. See how to release air out of a compressor.
  2. Drain the oil while it is warm, not hot. Warm oil flows more easily than cold oil. Let the unit cool enough to handle.
  3. Place a pan under the drain plug. Remove the plug and let the oil drain fully. Clean the plug and reinstall it, with a new gasket if the manual calls for one.
  4. Refill through the fill port with the grade the manual specifies. Fill to the middle of the sight glass or to the full mark on the dipstick, not to the top.
  5. Run the unit briefly, stop it, and check the level again. Top up slightly if needed.
  6. Dispose of the used oil properly. Take it to a recycling center or to an auto parts store that accepts used oil. Do not pour it down a drain or onto the ground.

Overfilling is a common mistake. Too much oil can carry into the air line and onto tools or finished work.

Signs the oil needs changing now

  • Dark, black, or varnished oil. Heat and time break oil down.
  • Milky or foamy oil, which can mean water has gotten into the oil.
  • A burnt smell.
  • Grit, or metal flakes when you drain it. If you see metal particles, stop and have the compressor checked.
  • Oil spitting into the air line or onto tools.
  • Oil that drops quickly or that you have to top up often.

Overfilling and oil in the air

Too much oil can turn into an oil mist that carries into the air line. That mist can damage tools, spoil paint and finishes, and contaminate work. Overfilling also raises pressure inside the pump.

Fill only to the mark, then check again after a brief run. If you overfilled, drain the excess through the drain plug until the level reaches the mark.

Frequently asked questions

Can I use motor oil in an air compressor?

Generally no. Motor oil contains detergents that cause foaming in compressors, and it is not formulated for compressor duty. Use compressor oil of the grade the manual lists, unless the manual says another oil is allowed.

How much oil does my air compressor take?

That depends on the model, and the manual is the reliable source. Check the fill specification and the sight glass or dipstick marks, rather than guessing.

The complete guide to maintenance and repair

Air Compressor Tips: Maintenance, Care and Upgrades
Read the guide

Keep exploring

Guides from other topics

All topics →