CFM (cubic feet per minute) measures how much air a compressor delivers each minute. PSI (pounds per square inch) measures how hard that air is pushed. A tool needs both: enough pressure to do the job and enough airflow to keep running. The two units measure different things, so one can’t be converted into the other.
What CFM measures
CFM is a measure of airflow, or volume per minute. It tells you how much air the compressor can supply to a tool or process over time. A tool that uses air continuously needs a steady supply of CFM, while a tool that uses short bursts needs less.
Compressor ratings are usually stated as CFM at a specific pressure. For example, a compressor might be rated at a certain CFM at 90 psi, as explained in what 4.0 SCFM at 90 PSI means. Airflow falls as pressure rises, so the same unit can deliver different CFM at different pressures. When comparing two compressors, check that both ratings are stated at the same pressure.
What PSI measures
PSI is a measure of pressure, or the force pushing the air. A tool needs enough pressure to drive its fastener, turn its bolt, or move its piston. The regulator on the compressor sets the pressure delivered to the tool, and the tank pressure must stay above that setting for the tool to work well.
Pressure is set by the compressor’s cut-in and cut-out settings and the regulator. Cut-in and cut-out pressure explains how the pressure switch decides when to run.
Why you can’t convert one into the other
CFM and PSI describe different properties. PSI is pressure, and CFM is a flow rate. Pressure and airflow are related in a compressor, because raising the pressure reduces the volume the compressor can deliver. That relationship doesn’t give you a formula that turns one number into the other. You need both numbers to know whether a compressor suits a tool.
How the two work together
Most tools list both values. The table below gives a general picture of how tool types compare. The exact figures vary by tool, so check the label on your tool.
| Tool type | Pressure need | Airflow need |
|---|---|---|
| Airbrush | Low | Low |
| Brad or nail gun | Moderate; many are rated around 70 to 90 psi | Low, in short bursts |
| Impact wrench | Moderate to high | Moderate to high, in bursts |
| Sander or grinder | Moderate to high | High, continuous |
| Spray painting | Varies with the gun type | High, continuous |
A nail gun is a good example of intermittent use. It draws air in short bursts, so a modest airflow can keep up. A sander runs continuously, so it needs a steady supply of air at its working pressure.
The common mistake: more PSI doesn’t mean more CFM
Raising the pressure setting doesn’t increase the airflow a compressor can deliver. Higher pressure usually asks more of the motor and pump, and it can reduce the free air the unit can supply. So a compressor with a high PSI number on the label isn’t automatically a high-airflow unit. Check the CFM value at the pressure your tool needs.
Reading a compressor spec sheet
- Find the CFM figure and the pressure it’s stated at. Compare units at the same pressure.
- Check the maximum pressure the compressor can reach, separate from the working pressure your tool needs.
- Look at tank size. A tank buffers short bursts, so a unit with a modest CFM rating can run some intermittent tools well.
- Look at the duty cycle. Continuous tools need a rating that suits long run times. Duty cycle explained covers how to read it.
Leaks, regulators, and tanks
Leaks waste airflow. Every leak in the hose, fittings, or tank takes some of the compressor’s output, and the motor runs more often to make up for it.
A regulator can lower the pressure reaching a tool, but it can’t raise the pressure above what’s in the tank, and it can’t create airflow the compressor doesn’t produce. The air receiver tank stores the air that the compressor delivers, so a larger tank can help a modest compressor keep up with bursts of demand.
How much CFM do I need?
Start with your tools. Check each tool’s CFM and PSI on its label, then consider how many run at the same time. Many guides suggest a margin above the tool’s listed airflow, because compressor ratings and tool ratings aren’t always measured under the same conditions (see CFM vs SCFM). The right margin depends on your work.
If you need continuous airflow at higher pressure, two-stage compressors are one type to compare. For the basic cycle that produces the air, see how an air compressor works.