Compressor Basics

Cut-In and Cut-Out Pressure: When Your Air Compressor Starts and Stops

Cut-in and cut-out pressure tell a compressor when to start and stop. Learn how the pressure switch uses them and why the gap between them matters.

On this page
  1. What cut-in and cut-out mean
  2. What the pressure switch does
  3. Why the gap between them matters
  4. Cut-in and cut-out versus the regulator
  5. Adjusting the settings safely
  6. When the switch doesn’t stop at cut-out
  7. Frequent starts: what to check first

Cut-in and cut-out pressure are the two tank-pressure settings that tell an air compressor when to start and stop. The pressure switch watches the tank. When pressure falls to the cut-in setting, the switch starts the motor. When pressure reaches the cut-out setting, the switch stops it. The gap between the two sets the range the tank cycles through.

What cut-in and cut-out mean

Cut-in is the tank pressure at which the motor starts. Cut-out is the tank pressure at which the motor stops. The difference between them is often called the differential.

For example, a switch set to start at 90 psi and stop at 120 psi has a differential of 30 psi. The numbers here are only an illustration. Your unit’s settings are set by the manufacturer.

What the pressure switch does

The pressure switch senses tank pressure and opens or closes the motor’s electrical circuit. On many piston compressors, the switch also controls the unloader valve, so the motor restarts without fighting trapped pressure. Loading and unloading explains that connection.

Some switches have an adjustment screw or dial. Many are preset at the factory and sealed. Check the owner’s manual before you assume your unit can be adjusted.

Why the gap between them matters

The differential sets how much air the tank can deliver between starts. A wider gap means the tank gives more air before the pressure falls back to cut-in. The motor then starts less often for the same amount of work.

A narrow gap means the motor starts again sooner. Frequent starts add heat and wear to the motor and the switch. The size of the tank matters here too: a larger air receiver tank holds more air across the same gap, so the motor runs less often.

Cut-in and cut-out versus the regulator

The pressure switch controls tank pressure. The regulator controls the pressure that reaches your tool. A tank can cut out at a higher pressure than your tool needs, and the regulator steps it down to the working pressure you set.

Adjusting the switch doesn’t change the regulator, and adjusting the regulator doesn’t change cut-in or cut-out. What CFM and PSI mean explains why the tool’s pressure and airflow both matter.

Adjusting the settings safely

  • Check the rated maximum first. The tank’s nameplate and the manual give the maximum allowable working pressure. Never set cut-out above that rating.
  • Don’t modify the switch to suit a tool. Set the regulator to the tool’s pressure instead. The switch’s job is tank pressure.
  • Follow the manual’s steps. Depressurize and unplug the unit before you work on the switch, and watch the gauges through a full cycle after any change.
  • Stop if the setting seems wrong. If you can’t find a rating or the switch behaves unexpectedly, contact the manufacturer.

When the switch doesn’t stop at cut-out

If the motor keeps running past cut-out, turn the unit off and unplug it. Don’t rely on the safety relief valve to do the job. The relief valve is a backup. It opens when pressure rises above a safe level and vents air, so repeated venting is a sign that something needs attention.

Have the switch checked or replaced by a qualified person or the manufacturer before you run the unit again.

Frequent starts: what to check first

If the compressor starts and stops more than it should, check these in order:

  1. Leaks. Look at fittings, hoses, the drain valve, and the switch. Soapy water on the fittings shows where air is escaping. Leaks make the motor run more often for the same work.
  2. The check valve. A leaking valve lets tank air return to the pump, so the pressure falls and the motor restarts sooner.
  3. Tool demand. Several tools running at once, or a tool that uses more air than the unit can supply, leads to more frequent starts.
  4. Run time and rating. If the unit runs close to its duty cycle limit, it may need a larger tank or a more suitable unit.

For the full cycle that the switch controls, see how an air compressor works.

The complete guide to compressor basics

How an Air Compressor Works: Parts and Principles Explained
Read the guide

Keep exploring

Guides from other topics

All topics →