Compressor Basics

What does OSHA say about compressed air?

OSHA limits using compressed air for cleaning to below 30 psi, with guarding and protective gear, and sets basic rules for tools and hoses in US workplaces.

On this page
  1. The 30 psi cleaning rule
  2. Securing tools and hoses
  3. Why compressed air is hazardous
  4. Safe-use checklist
  5. Hoses and trip hazards
  6. Outside the United States

OSHA, the U.S. Occupational Safety and Health Administration, allows compressed air to be used for cleaning only when it has been reduced to less than 30 psi. Even then, the cleaning must use effective chip guarding and personal protective equipment. The same standards also cover how pneumatic tools and hoses should be secured. These rules apply to U.S. workplaces. Other countries and some U.S. states have their own rules.

The 30 psi cleaning rule

The general industry standard, 29 CFR 1910.242(b), and the construction standard, 29 CFR 1926.302(b)(4), both say that compressed air shall not be used for cleaning unless it has been reduced to less than 30 psi. When it is, the work needs effective chip guarding and personal protective equipment.

In practice, cleaning with compressed air requires three things at once: pressure reduced below 30 psi, effective chip guarding, and personal protective equipment. Safer alternatives include vacuums with filters, brooms, or wet sweeping, and those are usually the better choice. Where compressed air is the only option, keep the pressure low and wear eye protection and the other protective gear the task calls for.

Securing tools and hoses

The general industry standard calls for pneumatic tools to be secured to the hose by a positive means, such as a locking device or a short wire, so the tool can’t come loose under pressure. It also calls for a safety clip or retainer on attachments, so a chisel, bit, or fastener can’t be ejected while the tool is running.

Use hoses and fittings rated for at least the compressor’s maximum pressure, and don’t run a tool above the manufacturer’s rating.

Why compressed air is hazardous

Compressed air causes injuries in several ways:

  • Debris. An air jet can blow particles into eyes and onto skin, and it can throw dust into the air people breathe.
  • Air injection. Compressed air forced into the body through a break in the skin or an opening can cause an air embolism, which is a serious medical emergency. Never direct air at skin or into the mouth, ears, or nose.
  • Noise. Compressors and air tools are loud (soundproofing a compressor helps), and hearing loss builds up over time. OSHA’s noise standard, 29 CFR 1910.95, covers workplace noise exposure.
  • Flying parts. Attachments and fasteners can be ejected from a tool.
  • Whipping hoses. A hose that disconnects under pressure can whip around and strike someone.

Safe-use checklist

  • Inspect hoses regularly for cuts, bulges, and abrasions. Tag and replace damaged hoses.
  • Depressurize the line before connecting or disconnecting a tool or hose.
  • Keep the shut-off valve for the air supply where you can reach it quickly.
  • Don’t carry a pneumatic tool by its hose.
  • Guard moving parts on the compressor, such as belts, pulleys, and flywheels.
  • Keep the compressor’s ventilation openings clear, and run it in a ventilated area.
  • Wear eye protection and hearing protection.
  • Never point an air gun or nozzle at anyone, and never dead-end it against yourself or someone else.
  • Train workers who use compressed air on the hazards and the safe methods.

Hoses and trip hazards

Hoses laid across walkways or curled on the floor are trip hazards. Store them on a hose reel or hang them, away from heat, oil, and sunlight. Keep the ends of hoses secured so they won’t whip if a connection fails.

Outside the United States

The rules above are U.S. federal standards, and they apply to U.S. workplaces. Other countries set their own requirements, and some U.S. states run their own workplace safety plans. If you work outside the U.S., check your national or local rules. For the full text of the U.S. rules, see the OSHA website at osha.gov.

For the pressure and tank side of compressed air safety, see how an air compressor works and air receiver tanks. The tank’s relief valve and nameplate limits are part of that picture. For matching tool pressure to what the compressor delivers, see what CFM and PSI mean.

The complete guide to compressor basics

How an Air Compressor Works: Parts and Principles Explained
Read the guide

Keep exploring

Guides from other topics

All topics →