Vehicle and Tire Air

What size air compressor do I need to fill tractor tires?

Filling tractor tires needs tank size and maximum pressure more than airflow. Learn what to look for in a compressor and how to inflate big tires safely.

On this page
  1. Why tractor tires ask more of a compressor
  2. Tank size and maximum pressure
  3. Power source: 120V, 240V, cordless or gas
  4. Choosing by job
  5. Set the pressure from the tire maker’s chart
  6. Inflating large farm tires safely
  7. Common mistakes

To fill a tractor tire, tank size and maximum pressure usually matter more than airflow. Published buying guides often point to a compressor with a tank of about 10 to 30 gallons and a maximum pressure of roughly 125 to 150 PSI. The tank stores air between pump cycles, so the pump does not have to build pressure from nothing. A small pancake unit or a 12-volt pump can take a long time to fill a large tire and may struggle to seat its bead.

Why tractor tires ask more of a compressor

Large tires hold a lot of air, so filling one from low pressure takes volume. Many farm tires run at fairly low pressures compared with car tires, which means the target is often modest, but getting there from a flat tire still means moving a large volume of air. The pressure ceiling of the compressor also needs to be high enough to seat the bead, the edge of the tire that sits against the rim.

The target pressure for any tire comes from the tire maker’s inflation chart, not from the number on the sidewall.

Tank size and maximum pressure

Tank size. A tank stores compressed air between pump cycles, so the motor does not have to keep running to build pressure. Portable shop units in the 10 to 30 gallon range are a common choice for tractor work, and larger shop units go higher.

Maximum pressure. Published guides often suggest a maximum in the range of about 125 to 150 PSI for tractor tires. Check the rating on the spec sheet rather than assuming it.

Airflow. Airflow (CFM) matters most if you also plan to run air tools, such as an impact wrench. For pure inflation, tank size and maximum pressure matter more.

Power source: 120V, 240V, cordless or gas

  • 120-volt portable units. Many portable units with a 10 to 30 gallon tank run on a standard household outlet. They suit topping off and occasional full fills.
  • 240-volt shop units. Larger permanent units, often in the 60 to 80 gallon range, need a 240-volt supply and suit a regular workshop.
  • Cordless high-output inflators. Some can top off a tractor tire in an emergency. They are slow for a full fill from flat.
  • Gas-powered portable units. These work well in the field and give good airflow. They produce carbon monoxide, so never run one in an enclosed building, including a barn or shed.

For tractor-mounted and field options, see PTO and belt-driven air compressors.

Choosing by job

  • Topping off low tires at home or on a small utility tractor: a portable 10 to 30 gallon electric unit is usually enough.
  • Full refill of large rear tires: a larger shop unit, or a gas-powered portable unit that can deliver good airflow.
  • Working in the field: a PTO-driven or engine-driven unit, so you do not have to bring the tractor back to a power supply.

If you are unsure whether you need a top-up or a full refill, check the tire first. A tire that looks flat may be low, but the refill job is very different if the tire has come off its bead.

Set the pressure from the tire maker’s chart

Use the tire maker’s inflation chart, which matches the load on the tire to a pressure. Do not inflate to the sidewall maximum. The chart is the right reference for farm tires, which are often run at lower pressures than car tires.

Inflating large farm tires safely

Large tires can fail during inflation, so take care:

  • Never stand over the tire or in line with the bead. Stand to the side.
  • Use a clip-on chuck and a long hose so you can work from a distance.
  • Where a tire cage is available, use one. Tire shops use cages for large tires for this reason.
  • Fill in steps and check the gauge between each one.
  • Keep the compressor’s tank drained and its pressure relief valve in working order.
  • If a tire has come off its bead, or the bead will not seat, stop pumping and have a tire shop deal with it.

Common mistakes

  • Choosing a compressor on airflow alone and ignoring tank size.
  • Trying to refill a large tire with a 12-volt or small pancake unit.
  • Inflating to the sidewall number rather than the chart pressure.
  • Running a gas-powered compressor in an enclosed space.

For how long a fill takes, see how long it takes to fill a tire with an air compressor. For pump speed and what the RPM ratings mean, see what rpm an air compressor should run at.

The complete guide to vehicle and tire air

Vehicle Air Pumps and Tire Inflators: A Buyer's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →