Short answer
A used air compressor can be a good value, but only if the tank is sound and the unit runs properly under pressure. Check the tank first. If the tank looks damaged, rusted through, or bulged, walk away. Do not pressurize a tank you do not trust.
Start with the tank
The tank is where the danger is. A compressor tank holds air under pressure, and a weakened tank can fail.
Look for:
- Rust, pitting, or flaking, especially on the bottom of the tank, where water collects.
- Dents, bulges, or distorted areas, and any cracks or signs of previous repair.
- Bubbling or peeling paint over rust.
- Corrosion around welds, feet, and fittings.
Find the tank’s data plate or manufacturer tag, if it has one. It can show the maximum working pressure and when the tank was made. If there is no tag, or the tank looks old, ask a qualified inspector to assess it before you use it. Do not assume a tank is safe because it has held air before.
Drain it and look at what comes out
Open the drain valve at the bottom of the tank. A little water is normal, because compressed air carries moisture. Heavy rust, chunks of rust, sediment, or a large amount of water can mean the inside of the tank is corroding. Treat that as a reason not to buy.
Check the safety (relief) valve
The relief valve is a safety device that vents air if the pressure gets too high. It should open when the pressure exceeds its setting and then close again. Do not disable, plug, or bypass it. If it does not work, do not buy the unit until it is repaired or replaced.
Test it with care. Wear eye protection, and stand to the side of the valve when you test it. If you are not sure how to test it, ask the seller to show you, or ask a qualified technician to check it.
Run it: the live test
Ask the seller to run the unit up to full pressure while you watch. Our compressor testing and inspection checklist covers what to look for.
- Watch the gauges. They should read sensibly as the tank fills.
- Confirm the automatic shutoff turns the motor off at the set cut-out pressure.
- Test the regulator. The output pressure should adjust smoothly up and down.
- Listen for knocking, rattling, grinding, or heavy vibration.
- Watch for overheating, such as a burning smell or dark residue on the motor or pump.
If the seller will not run the unit, treat that as a reason to walk away.
Check the oil and smell
On oil-lubricated units, check the oil sight glass or dipstick. Cloudy or milky oil can mean water is in the crankcase. A strong burning smell can point to internal wear or overheating. Oil-free units have no oil to check, but still need the other checks.
Look for air leaks
Paint soapy water on the fittings, the quick-connects, and the check valve where the air enters the tank. Bubbles show leaks. Small leaks at fittings are often easy and cheap to fix. Leaks that you can hear or that keep the motor running are a bigger concern, because they waste energy and can hide other faults.
Check the specs that matter
- Airflow at 90 PSI, in CFM or SCFM, compared with the tools you plan to run. Do not rely on horsepower alone. See CFM vs SCFM.
- Voltage and amps on the nameplate. Check that your outlet and circuit can supply them. See 120V vs 240V air compressors.
- Type: oil-free or oil-lubricated, and whether it is portable or stationary. See portable vs stationary air compressors.
Plan for hidden costs
A used unit can cost more than its price once you add:
- Hoses, couplers, and a regulator, if they are missing or worn
- Replacement switches, check valves, seals, or fittings
- Electrical work, such as a new outlet or circuit
- Transport, moving, and any professional inspection
Add these up before you decide that a used unit is a bargain.
Private seller or dealer
A dealer may offer a return window or a short warranty, and may test the unit before sale. A private seller usually does not offer either. Weigh that difference against the price. If you buy privately, insist on a live test and a full inspection before payment.
Red flags: walk away if you see these
- Bulges, deep rust, or cracks in the tank
- A relief valve that does not vent or reseat
- A pump that will not reach full pressure
- Heavy knocking, grinding, or excessive vibration
- Water or rust coming out of the drain in quantity
- The seller will not run the unit or will not let you test it
- Missing or illegible tank information, and no way to have it checked
Bottom line
Inspect the tank first, check the relief valve, run the unit under pressure, and look for leaks. If the tank is in doubt, do not buy the unit, and do not try to pressurize it to find out. For the wider purchase decision, see air compressor types and sizes.