Choosing a Compressor

How much PSI is a pancake compressor?

Most 6-gallon pancake compressors list about 150 PSI maximum tank pressure. Here's what that number means and how it relates to your tools and tires.

On this page
  1. Short answer
  2. Maximum tank pressure vs. working pressure
  3. What pressure your tools need
  4. Why 90 PSI shows up on spec sheets
  5. Airflow matters more than max PSI for most tools
  6. Inflating tires
  7. Safety: hoses, fittings, and tools
  8. Quick checklist for reading a spec sheet
  9. Where this fits in buying a compressor
  10. Bottom line

Short answer

Most 6-gallon pancake compressors list a maximum tank pressure of about 150 PSI. Some list 175 PSI, and a few specialized models list higher. That number is the tank’s rating, not the pressure your tools will run at. Check the label or spec sheet for the exact model you are considering.

Maximum tank pressure vs. working pressure

Two numbers matter here, and they are easy to confuse:

  • Maximum tank pressure is how high the compressor fills the tank before the pressure switch shuts the motor off.
  • Working pressure is what reaches your tool. A regulator sets it, and a gauge shows it.

The tank can hold far more pressure than your tool should receive. Set the regulator to the level your tool needs, not to the tank’s maximum.

What pressure your tools need

Most pneumatic tools list an operating pressure range in their manual. Many nailers and staplers are designed to run well below a tank’s maximum. Set the regulator at or below the tool’s listed maximum, and never above it.

If you do not have the manual, look on the tool itself or on the manufacturer’s site before you connect the air line.

Why 90 PSI shows up on spec sheets

Airflow is often rated at 90 PSI. That is a common reference point, so manufacturers can compare units. It does not mean every tool runs at 90 PSI. It means the airflow number applies at that pressure.

For most tools, the airflow at the tool’s operating pressure matters more than the tank’s maximum PSI.

Airflow matters more than max PSI for most tools

A typical 6-gallon pancake compressor delivers somewhere around 2 to 3 standard cubic feet per minute at 90 PSI, according to the figures many spec sheets and reviews give. Check the exact label, because models differ.

Airflow at lower pressure can be higher. That is why the same unit can show a bigger number at 40 PSI. Do not compare a 40 PSI figure with a tool’s 90 PSI requirement. For more on reading these ratings, see CFM vs SCFM and what does 4.0 SCFM at 90 PSI mean.

Inflating tires

Car and light-truck tires are normally set well below 50 PSI. The correct pressure is on the placard inside the driver’s door jamb, and the tire’s maximum pressure is printed on its sidewall.

A 150 PSI tank is far more than a tire needs. Never inflate a tire above the sidewall maximum, and check the pressure with a gauge after you fill it.

Safety: hoses, fittings, and tools

  • Use the regulator. Do not connect a tool directly to a higher tank pressure than it is rated for.
  • Check that hoses, couplers, and tools are rated for the pressure you set.
  • The lowest rating in the air line sets the safe limit. A high-pressure tank does not raise the rating of a weaker hose or fitting.
  • Wear eye protection when you work with compressed air.
  • Replace cracked or bulging hoses.

For more on what a compressor is safe to use for, see can you use an air compressor for cleaning.

Quick checklist for reading a spec sheet

  • Maximum tank pressure
  • Regulated output range
  • Airflow (CFM or SCFM) at 90 PSI
  • Tank size
  • Duty cycle

Where this fits in buying a compressor

A pancake’s PSI rating is one number among several. For most home buyers, the more useful questions are how much airflow the unit gives at 90 PSI and whether that airflow covers the tools they plan to run. The air compressor types and sizes guide walks through the full comparison, and is a 3 gallon air compressor big enough covers a smaller unit.

Bottom line

A pancake’s 150 PSI rating tells you how much pressure the tank can hold. It does not tell you what your tools need. Set the regulator for your tool, check the airflow at 90 PSI, and keep every part of the air line rated for the pressure you use.

The complete guide to choosing a compressor

Air Compressor Types and Sizes: How to Choose the Right One
Read the guide

Keep exploring

Guides from other topics

All topics →